ASTM D1200 PDF

adminComment(0)

Scope This test method covers the determination of the viscosity of Newtonian or near-Newtonian paints, varnishes, lacquers, and related liquid materials with the Ford-type efflux viscosity cup. Referenced Documents ASTM Standards: 2 D Test Methods for Rheological. - cSt. The orifices are manufactured from stainless steel. ( approximately). FORD FLOW CUP. Ford Flow Cup No 1 - ASTM D RL-A-FC -ASTM1. D() Standard Test Method for Viscosity by Ford Viscosity Cup Ford viscosity cups~ Format, Pages, Price. PDF ASTM License Agreement.


Astm D1200 Pdf

Author:MARISA OMINELLI
Language:English, Portuguese, Hindi
Country:Botswana
Genre:Technology
Pages:577
Published (Last):09.12.2015
ISBN:778-4-39585-814-7
ePub File Size:18.72 MB
PDF File Size:19.27 MB
Distribution:Free* [*Registration Required]
Downloads:28739
Uploaded by: LARITA

VISCOSITY CUP ASTM D 'FORD' DIP-TYPE. VF PRODUCT DESCRIPTION. Viscosity Cup Immersion Ford is a titanium anodized aluminum viscosity. ASTM D - Designation: D – 10 Standard Test Method for Viscosity by Ford Viscosity. ASTM D Standard Test Method for Viscosity by Ford Viscosity Cup. ALSO SEE ASTM D (R). Format. Details. Price (USD). PDF. Single User. $

Particular care must be exercised in cleaning the ori?

General Help

Test Specimen 7. Temperature of Testing 8. Temperature drift during the test should be kept to a minimum and should not exceed NOTE 2— It is impossible to predict the effect of temperature change on each material with which the apparatus may be used.

Calibration 9. The frequency of this calibration check depends upon the amount of use and the care that the individual cup receives. Report Precision and Bias Keywords Calibration Procedure for Ford Cups X1. A small change in diameter of the ori?

Títulos relacionados

Bring this cup and the liquid viscosity standard to a constant temperature as close as possible to Determine the time of efflux to the nearest 0. Keep the temperature drift to within Box 16, State College, Pa. For particular oils applicable for use with the Ford Cups refer to Table X1.

Oils available from other sources, having known kinematic viscosities, may also be used. A percent correction can be applied to the seconds?

You might also like: ASTM D EBOOK

Terminology 3. If the ratio of shear stress to shear rate is not constant, the liquid is nonNewtonian. Summary of Test Method 4.

Signicance and Use 5. Apparatus 6.

ASTM D()

The orice dimensions are considered as a guide only as the combination of cup and orice dimensions must permit conformance to the ow formula for each cup as listed in the Appendix.

NOTE 1If the orice is removed from the cup for any reason the cup should be recalibrated before use as described in the Appendix. Current edition approved May 15, Published June Originally approved in Last previous edition approved in as D 94 Test Specimen 7.

D 94 reciprocating shaker in a pint can two-thirds full. Allow to stand undisturbed for 10 min while adjusting further to the desired temperature.

Make the viscosity determination at the end of the min period. Procedure For the highest degree of precision the room temperature should be between 22 and 28C 72 and 82F.

Determinations should be made at a temperature above the dew point of the atmosphere surrounding the apparatus.

Fill the cup with the prepared specimen. The preferred method is to overll the cup and scrape off the excess with a straightedge. Calibration 9.

Popular Publishers

The frequency of this calibration check depends upon the amount of use and the care that the individual cup receives. Conditioning Precision and Bias Keywords Calibration Procedure for Ford Cups X1.

A small change in diameter of the orice becomes signicant in the results obtained with the use of this type of viscosity-measuring apparatus. Bring this cup and the liquid viscosity standard to a constant temperature as close as possible to Determine the time of efflux to the nearest 0.

Keep the temperature drift to within If the temperature is not 77F, the actual temperature must be noted and the viscosity of the standard oil corrected to this temperature. Box 16, State College, Pa.

For particular oils applicable for use with the Ford Cups refer to Table X1. Oils available from other sources, having known kinematic viscosities, may also be used.

A percent correction can be applied to the seconds ow when the cup is in normal use. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

ASTM D Flow Cups – ASTM D Ford No 2

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.Apparatus 6. Summary of Test Method 4. Oils available from other sources, having known kinematic viscosities, may also be used. A small change in diameter of the orice becomes signicant in the results obtained with the use of this type of viscosity-measuring apparatus. Make the viscosity determination at the end of the min period.